Welcome: JIA LI INDUSTRIAL (H.K.) LIMITED
Language: Chinese ∷  English

Fastener Teach

Vibration Testing of Locking Washers: Test Design, Criteria and Reading the Results

Vibration Testing of Locking Washers: Test Design, Criteria and Reading the Results

Locking washer datasheets claim excellent locking performance, but such claims need test evidence or they are marketing. The principle is simple: clamp the joint to a defined preload, apply reciprocating transverse or axial displacement, and record how preload decays with cycles. The difficulty lies in setup and interpretation - amplitude, frequency, clamp length and surface condition can each flip the conclusion. Reading a report properly matters more than obtaining one.

Why transverse testing dominates

In real joints, loosening comes mainly from transverse micro-motion between contact faces rather than axial loading. Transverse displacement lets the bolt relax slightly and the nut back off a little each cycle, so preload drops. The transverse vibration test, commonly called the Junker test, reproduces exactly this: transverse displacement on clamped plates with a sensor logging preload decay. It discriminates between locking features far better than axial vibration, which is why it became the mainstream method.

Parameters: amplitude, frequency, clamp conditions

Setup decides severity. Larger amplitude and higher frequency loosen faster, but too large an amplitude destroys an ordinary nut within minutes and removes any discrimination. Clamp length changes system elasticity: a long bolt has more elastic reserve and decays more gently, while a short clamp is harsher and closer to thin-plate reality. Surface roughness, paint or lubricant, and washer stacking order all shift results noticeably, so the report must state them.

Criteria: residual preload or rotation

Two criteria are common. Residual preload: after a defined number of cycles, preload must stay above a percentage of the initial value. Rotation or relative displacement: measure how far the nut has turned relative to the bolt and fail beyond a threshold. The first is intuitive, the second closer to the failure mechanism. Thresholds must match the application - rail transit and general machinery do not sit at the same level, and comparing bare numbers across reports is misleading.

Three typical curve shapes

A fast-drop curve loses preload steeply in the first few hundred cycles, then flattens: usually contact faces bedding in, or the locking feature not yet working. A slow linear decline is typical of friction-dependent plain nuts, continuous with no inflection. A plateau curve, falling to a level and then holding, is the signature of a good locking design. Curve shape often carries more information than a single final value. A step change early in the curve usually means the washer teeth have collapsed or the thread slipped once - worth asking the supplier to explain, rather than checking only whether the verdict says pass.

Common misreadings

Bench tests are accelerated and simplified, and cannot be equated with field life. Avoid three misreadings: treating a pass as never loosening, while ignoring site factors such as low torque or painted faces; comparing data across different conditions, for instance reports with different amplitude and clamp length; and reading only the final value, missing early rapid decay that may already break a seal. Align test conditions, criteria and your own duty before interpreting. One more point: bench samples are new and dry, while the site may hold oiled parts that have been apart several times - and that gap is often larger than the gap between brands.

Specifying a usable test report

When requesting reports, ask for the rig and clamp arrangement, initial preload and how it was applied, amplitude and frequency, cycle count, sample quantity with material and coating condition, criteria and verdict, plus full curves rather than single points. A one-line conclusion or a photograph cannot support selection. For critical projects, request third-party reports or re-testing of actual samples.

From bench to site

Passing a test is only the start. Three site conditions should match the test: torque at design value, contact faces free of paint and burrs, washers installed in the correct orientation and order. During maintenance, torque sampling or witness marks reveal relative rotation as an early loosening signal. On long-running equipment, periodic inspection records protect the joint better than a one-off selection decision.

Closing: selection begins with reading evidence

Choosing locking washers comes down to reading the evidence. On imported locking components we supply original test data and batch documents, and can run comparative sample tests against the customer's actual duty - turning locking performance from a slogan into a checkable parameter.

Scan the qr codeClose
the qr code